Black Pelican 1060 Case
One Black Pelican 1060 case ready for your camouflage job.
$19 plus S&H
Camouflaged Pelican 1040 Case
One Pelican 1040 Camouflaged Case in a Mossy Oak pattern.
$28.50 plus S&H
Black Pelican 1040 Case
One Black Pelican 1040 case ready for your camouflage job.
$16 plus S&H
Power Switch
Power Switch with spade terminals rated for 10 amps
$2 plus S&H
Rubber Coated Eye Bolts
Two 1/4" rubber dipped eye bolts with four 1/4" nuts.
$5 plus S&H
Uncoated Eye Bolts
Two 1/4" metal eye bolts with four 1/4" nuts.
$2.50 plus S&H
1 1/4" Glass Lens
1 1/4" Glass Lens for covering flash and/or shutter holes.
$2.00 plus S&H
.65" Fresnel Lens
One Fresnel Lens with a .65" focal length
Wide Angle Fresnel Lens
One Wide Angle Fresnel Lens with .9" focal length
Flash Enhancer
One Flash Enhancer Fresnel Lens used to focus your camera's flash into a narrower beam and get more distance from your camera's flash.
$3.50 plus S&H
AA battery holder without internal switch
Four AA battery holder with 6" tinned leads (ready for soldering) and single sided tape on back of battery holder.
$1.50 plus S&H
AA battery holder with internal switch
Four AA battery holder with 6" leads and two conductor quick disconnect ready for connection to the YetiCam board. The battery holder has a cover and internal switch for the ultimate in convenience!
9 Volt battery holder with internal switch
One 9 Volt battery holder with 6" leads and two conductor quick disconnect ready for connection to the YetiCam board. The battery holder has a cover and internal switch for the ultimate in convenience!
$2.25 plus S&H
9 Volt battery holder with quick connector
One 9 Volt battery holder with 6" leads and two conductor quick disconnect ready for connection to the YetiCam board.
YetiCam Control Board Power Cable
One 2 conductor cable with quick disconnect ready for connection to the YetiCam board.
$1 plus S&H
YetiCam Control Board Accessory Cables
Two 2 conductor cables with quick disconnects ready for connection to the YetiCam board.
Four Wire Stereo Plug Assembly
2.5 mm Four Wire Stereo Plug Assembly with 4 wire stereo jack and 4 wire stereo plug . This assembly is perfect for Sony DSC-S600 modifications and the jack will snap into tripod hole
$7 plus S&H
Four Wire Stereo Jack
2.5 mm Four Wire Stereo Jack that will fit nicely into the tripod hole on a Sony DSC-S600.
$3 plus S&H
Four Wire Stereo Plug Assembly for A503
Four Wire SMT Stereo Plug Assembly with 4 wire stereo jack and 4 wire stereo plug . This assembly is perfect for the Samsung A503 modifications and it is shown in our modification document.
Four Wire SMT Stereo Jack
Four Wire SMT Stereo Jack that will work with the Samsung A503 modification
Four Wire Stereo Plug
2.5 mm Four Wire Stereo Plug cable. This extra cable can be used to make a spare cable on a S600 that has had the lens modifications done allowing the camera to be used outside of the unit
$4 plus S&H
Four Wire Servo Jumper for S40 Lens Mods
Four Wire servo plug with jumper installed. This connector can be installed into the S40 servo assembly when the camera is out of the unit allowing the camera to be used outside of unit once the lens modifications have been completed
YetiCam Control Board DIP Switch Stickers
Paper sticker with DIP switch settings printed on label for mounting inside camera enclosure. (One included with board purchase)
1" IR Circle
One 1" IR Passing filter. This filter blocks most of the light below 700 nM (visible light) and pass the IR light. You can glue this filter on top of your shutter glass or the preferred method is to cut a 1" hole in the flash gasket and press this filter in.
$3.00 plus S&H
Three Wire Servo Assembly
Three wire servo assembly with 30 gauge wires PROFESSIONALLY crimped on one side and 24 gauge stranded wires PROFESSIONALLY crimped on the other side.
$6 plus S&H
Four Wire Servo Assembly
Four wire servo assembly with 30 gauge wires PROFESSIONALLY crimped on one side and 24 gauge stranded wires PROFESSIONALLY crimped on the other side.
Five Wire Servo Assembly
Five wire servo assembly with 30 gauge wires PROFESSIONALLY crimped on one side and 24 gauge stranded wires PROFESSIONALLY crimped on the other side.
$7.50 plus S&H
Six Wire Servo Assembly
Six wire servo assembly with 30 gauge wires PROFESSIONALLY crimped on one side and 24 gauge stranded wires PROFESSIONALLY crimped on the other side.
$8 plus S&H
Five Wire Servo Assembly for External Power
Five wire servo assembly with three 30 gauge wires PROFESSIONALLY crimped on one side and three 24 gauge stranded wires PROFESSIONALLY crimped on the other side. The other two wires are 22 gauge wire for handling the additional current associated with connecting external batteries on a camera.
Flat Flex Cable for Shutter Assembly
Flat flexible cable that can be use for Sony P41 and P32 shutter assembly.
Power Mosfet Cable
Power Mosfet Cable Assembly used to connect slave flash to the YetiCam control board as detail here: Slave Flash The cable comes ready to wire the Black, Green and Red wire to the designated spots on the YetiCam board. All three resistors are soldered into place and are then covered with heat shrink tubing.
Flash Gasket Foam
One piece of foam used to make flash gaskets. This foam has one sticky side for adhering to case. The foam is 5/16" X 3" X 4". This works well on the Sony DSC-S600.
Four 7/8" threaded standoffs
Four 7/8" threaded nylon standoffs for use in the YetiCam kit when using a Wide Angle Fresnel Lens.
Four 1" standoffs
Four 1" nylon standoffs for mounting of board.
Control Board Mounting Bracket Kit Regular Lens
Machined control board mounting bracket for use with a regular Fresnel Lens (ordered separately). Bottom of bracket is machined out to accommodate double sided stick tape and Fresnel lens. Kit comes with bracket, double sided tape, 4 machine screws, four stand offs, and 4 pan head screws. Just cut a 1" hole in the case and glue this down. No external screw holes and the distance from the PIR to the lens is all set for a horizontal mounted board. (Assembly Document)
$10.00 plus S&H
Control Board Mounting Bracket Kit Wide Angle Lens
Machined control board mounting bracket for use with a Wide Angle Fresnel Lens (ordered separately). Bottom of bracket is machined out to accommodate double sided stick tape and Fresnel lens. Kit comes with bracket, double sided tape, 4 machine screws, four stand offs, and 4 pan head screws. Just cut a 1" hole in the case and glue this down. No external screw holes and the distance from the PIR to the lens is all set for a horizontal mounted board. (Assembly Document)
1040 PVC Pipes
Machined PVC pipes for pipe through design in a 1040 case. This pipe is cut to the correct length for mounting through the purge hole with a 5/8" hole drilled. The inside of the pipe is machined out to make a Python Cable pass through easier. This pipe is the same as is used in our kits.
Python Lock
Camouflage Python Cable Lock with 5/16" X 6' cable.
$15.00 plus S&H
1040 Pelican Case Seal
Round case seal gasket to replace the pelican bladder. This material gives you a cleaner look and a better seal.
1060 Pelican Case Seal
$4.00 plus S&H
Samsung A503 Flash Capacitor
Replacement flash capacitor for the Samsung A503. Please review modification document for details on installation.
$1.00 plus S&H
Zorb-It
Zorb-It is placed inside the case to control the formation of water due to temperature changes outside the case and humidity.
Neuros Power Supply Board
This board will convert 12 Volts to 5 Volts for control of the Neuros DVR.
$25.00 plus S&H
Soldout
YetiCam Control Board Camera Cable
One 4 conductor cable with quick disconnect ready for connection to the YetiCam board. (One included with board purchase)